New Teknamotor Skorpion 280 RB wood chipper
Ostrowiec Świętokrzyski
If you decide to buy equipment at a low price, make sure that you communicate with the real seller. Find out as much information about the owner of the equipment as possible. One way of cheating is to represent yourself as a real company. In case of suspicion, inform us about this for additional control, through the feedback form.
Before you decide to make a purchase, carefully review several sales offers to understand the average cost of your chosen equipment. If the price of the offer you like is much lower than similar offers, think about it. A significant price difference may indicate hidden defects or an attempt by the seller to commit fraudulent acts.
Do not buy products which price is too different from the average price for similar equipment.
Do not give consent to dubious pledges and prepaid goods. In case of doubt, do not be afraid to clarify details, ask for additional photographs and documents for equipment, check the authenticity of documents, ask questions.
The most common type of fraud. Unfair sellers may request a certain amount of advance payment to “book” your right to purchase equipment. Thus, fraudsters can collect a large amount and disappear, no longer get in touch.
- Transfer of prepayment to the card
- Do not make an advance payment without paperwork confirming the process of transferring money, if during the communication the seller is in doubt.
- Transfer to the “Trustee” account
- Such a request should be alarming, most likely you are communicating with a fraudster.
- Transfer to a company account with a similar name
- Be careful, fraudsters may disguise themselves as well-known companies, making minor changes to the name. Do not transfer funds if the company name is in doubt.
- Substitution of own details in the invoice of a real company
- Before making a transfer, make sure that the specified details are correct, and whether they relate to the specified company.
Seller's contacts
+48 41 263 ...
Show
+48 41 263 68 23
+48 41 263 ...
Show
+48 41 263 69 13
Poland 
Poland, Ostrowiec Świętokrzyski
Poland, Ostrowiec Świętokrzyski
Poland, Ostrowiec Świętokrzyski
Poland, Ostrowiec Świętokrzyski
Poland, Ostrowiec Świętokrzyski
Poland, Ostrowiec Świętokrzyski
Poland, Ostrowiec Świętokrzyski
Poland, Ostrowiec Świętokrzyski
Poland, Ostrowiec Świętokrzyski
Poland, Ostrowiec Świętokrzyski
Poland, Ostrowiec Świętokrzyski
Poland, Ostrowiec Świętokrzyski
Poland, Ostrowiec Świętokrzyski
Poland, Ostrowiec Świętokrzyski
Poland, Sokołów Podlaski
Poland, Opalenica
Poland, Mogilno
Poland, Podegrodzie
Poland, Słupia
Poland, Słupia
Large loading table, 265 mm wide and 190 mm high inlet allows chipping branches with offshoots (with leaves and needles) as well as a round timber of the diameter up to 180 mm.
A sector-type drum with three cutting knives (one rotation of the drum for one full cut) allows to achieve a very high potential of the chipper with a relatively low power of the tractor. Knives produced out of special alloy steel and properly heat treated - can be sharpened several times even 20 mm of the nominal size, assuring theirs long-term use.
Installed screen ensures high regularity if chips. Chips are advanced from under the screen to the fan by a screw conveyor, than discharged thorough the ejection tube. The chipper is equipped with manually swiveled by 360°ejection tube.
The feeding system consists of built on a rocker toothed roll of the diameter of 280 mm and a feeding table equipped with roll of the diameter of 200 mm, preceded by manually folded flap. This solution makes the loading much easier, improves the work of operator and increases the efficiency.
Safety of the operator of a chipper is ensured by a cable safety switch attached, which - by pulling the cord in any direction - causes the hydraulic feed system to stop immediately. Unlocking the system takes place by releasing / unlocking the EMERGENCY STOP button to the work position.
As a standard, the chipper is also additionally equipped with one of the most advanced electronic system of work control available on European market automatically protecting the propulsion system of the machine against overload/excessive duty through temporary stopping the feeding unit. Easily editable software of the No-stress system provides a simple way to change the settings of the machine adapting it to individual needs. Preset "thick wood" and "thin wood" modes allow fast and easy change of the operation of the chipper in order to match the current material to be shred and increase the effectiveness of work. Total- and daily- hour meter is built into this system.
Produced chips may be used as a solid fuel for heating, as a raw material for production of paper, furniture boards, and after additional disintegrating in a hammer mill for pellets and briquettes production.
Technical details:
Overall dimensions (L x W x H) 1775 x 1980 (2700)* x 2250 (3050)* [mm]
Weight 1100 [kg]
Branch diameter 180 [mm]
No of knives 3 cutting + 1 counter-knife
Feeding speed up to 22 [running meters/min]
Chipping capacity up to 10 [stère meters/h]
Chip width to 25 subject to material [mm]
Feeding unit - hydraulic feeder
Drum diameter 420 [mm]
Hopper dimensions (WxH) 265 x 190 [mm]
Type of drive tractor’s PTO
Min. power of tractor 60 [hp]
()* - unfolded, ready to work
Equipment included:
- PTO shaft
- Independent hydraulic system
- Adjustment of height of ejecting the chips
- Swivelled by 360° ejection tube with deflector.
- Electronic system of work control with hour meter.
show contacts